Fire Alarm And Accessories

RAVEL FIRE ALARM CONTROL PANEL

Ravel Indian Manufacturer, International standard. Switch Mode Power Supply. Modular Construction, Serviceable. Surface Mount Technology. Battery polarity & deep discharge protection. As per IS -15908: 2011 Standard. 16 X 2 Dot Matrix LCD Display. Standby battery backup with built in charging. Fire / Fault status in unambiguous colored LED indication. Switch Mode Power Supply. Tactile Keypad for easy panel operation. System on indication. Main, Standby status indication. Low Battery visual warning with audible tone. Relay output for actuators for Fire and Fault. Lamp Test facility Zone wise one man walk Test Facility. Zone wise Isolation facility with loop voltage cut off. Compatible to all type of Conventional Detectors. Optional Zone Wise Sounder / Zone Wise Contact.

RAVEL RESPONCE INDICATOR RE-RI

Features Compatible for 2 wire detectors. Alarm status is indicated By Red colour LED. Operates on 12 VDC. Dual LEDs for 360 visibility Flush / Ceiling wall mount

Siemens Control Module

Siemens Monitor Module

Fire Alarm Single Input Module

Relay Module

Sensor Hooter

Zxce Five Loop Fair Alarm Panel

ZXse+Intelligent+Fire+Alarm+Panel

DXc One Loop Fire Alarm Control Panel

DXc One Loop Fire Alarm Control Panel

Siemens Loop Isolator

Smoke Detector

Simplex 4098-9714 TrueAlarm Photoelectric Sensor / Detector 0742444CN The Simplex 4098-9714 TrueAlarm photoelectric sensors use a stable, pulsed infrared LED light source and a silicon photodiode receiver to provide consistent and accurate low power smoke sensing. Seven levels of sensitivity are available for each individual sensor, ranging from 0.2% to 3.7% per foot of smoke obscuration. Sensitivity is selected and monitored at the fire alarm control panel. The sensor head design provides 360 smoke entry for optimum response to smoke from any direction. A built-in screen keeps insects from entering the smoke chamber. Due to its photoelectric operation, air velocity is not normally a factor, except for impact on area smoke flow. This photoelectric detector can be used with the 4010 and 4100U series control panels from Simplex. It also is compatible with the 4008, 4020, 4210, and 4100 series, as well as with 2120 TrueAlarm CDTs. This high-quality sensor will ensure your system is always in proper working order, so place your order today and well ship it to you immediately.

Fire Alarm Horn Strobe Light

Honeywell 6W Ceiling Speaker HN-CL06

HM-PSE-S2 Smoke Detector Morley

Plastic HM MCP Glass Honeywell Morley Manual Call Point

Morley FHS-F Fire Fighters Remote Handset

FPJ-F Firefighter Phone Jack

Beam Detector 1224

Morley IAS Addressable Sounder Strobe

Mcp Siemens Fdm226-rg

Notifire Fire Alarm Control Panal Nfs640

COOPER SMOKE DETECTOR CAP320

Cooper CAP320 Intelligent Addressable Optical Smoke Sensor (MAP820 / FXN723 / 400002FIRE-0002X) These ranges of intelligent addressable sensors have been specifically designed to operate with Cooper intelligent addressable fire systems. All sensors are third party approved to the relevant section of EN54 (part 7 for smoke detectors & part 5 for heat detectors). The optical sensor (CAP320) is suitable for most applications giving the fastest response to slow burning or smouldering fires which give rise to large visible smoke particles.

COOPER CAF1100 FIRE ALARM CONTROL PANEL

PRODUCT NAME Eaton CF1000 Addressable control panel CATALOG NUMBER CF1100 PRODUCT LENGTH/DEPTH 90 mm PRODUCT HEIGHT 375 mm PRODUCT WIDTH 365 mm PRODUCT WEIGHT 7.516 kg COMPLIANCES Contact Manufacturer APPEARANCE CONSTRUCTION MATERIAL BACK ENCLOSURE Mild steel CONSTRUCTION MATERIAL FRONT ENCLOSURE ABS PRODUCT BRANDING Eaton Cooper CONFORMANCE / CERTIFICATION EN CERTIFICATION STANDARDS EN54 Pt2 (Control and Indicating Equipment) EN54 Pt4 (Power Supply Equipment) EN54-2:1997+A1:2006, EN54-4:1997+A1:2002+A2:2006 OTHER CERTIFICATION STANDARDS VdS ENVIRONMENTAL INGRESS PROTECTION IP30 INSTALLATION AUXILIARY FREE OUTPUT Yes AUXILIARY RELAYS Fire/Fault CABLE ENTRY LOCATION Top: 11 M20 Knockouts, Rear: 200 x 20mm opening CONSTRUCTION MATERIAL FRONT ENCLOSURE ABS EXTERNAL CONNECTION PORTS RS232 RS485 INTEGRATED FUNCTION Emergency Power Supply Integrated Interface External Addressable MAIN INPUT SUPPLY 230 Vac, 50 Hz MOUNTING METHOD Surface mounting SUITABLE FOR Bus Connection TYPE OF DISPLAY Touchscreen

SIEMENS MINI MONITOR MODULE

The Siemens Fire Safety Intelligent Interface Module (Model XTRI-M) is designed to provide the means of interfacing direct shorting devices to the fire-alarm control panel (FACP) loop circuit. The module uses one (1) address on the loop. Each XTRI-series interface module provides the built-in ISOtechnology feature - intelligent dual isolation meeting NFPA 72 Class X (Style 7) wiring requirements. Up to 252 isolation ready devices per loop and in mixed mode a maximum of 30 non-isolated devices between isolated devices (wired in polarity-insensitive mode). Additionally, the devices between isolators can either be H-series or the more contemporary X-series detection devices.

COOPERHEAT DETECTOR

The heat sensor (CAH330) can be set to one of 3 modes 77C / 92C and rate of rise. These sensors are designed to be used in environments where the ambient conditions might cause false alarms if smoke detection were to be used, for example where there is a high level of dust, fumes, steam or smoke under normal conditions.

Ravel heat detector RE-316H2L

The RE 316H-2L Conventional detectors are designed to work with all conventional Panels. These detectors are low profile and have O dual LEDs for 360 visual indication. The blinking LEDs indicate normal operating conditions whereas the steady state indicate fire status. RE 316H-2L is a fixed cum rate of rise heat detector using a thermistor. These detectors will raise an alarm when the detector O reaches 59 C(Fixed) or when the change in temperature exceeds O the rate of rise of 11 C / min.

RAVEL CONVENSNAL MULTY DETECTOR RE 316SH - 2L

Electrical Specification Operating Voltage : 9 ~ 33V DC Reset Voltage : less than 1V Start-Up Current : 120 A. Alarm Current : 40 mA (Max) Remote Output : 15 mA maximum open collector Thermal Rating : 59 C (138 F) Rate of Raise of Temp : 11.1C / min (20F/min) Smoke Sensitivity : (1.9 0.76) % / ft Air Velocity : 0 4000 fpm. Operating Temperature : -10 C to 37.8 C Humidity : 0 95% RH, non-condensing Mechanical Specification Height : 46 mm with base Diameter : 100 mm dia Weight : 130 g with base IP Rating : IP 42

MANUAL CALL POINT CBG370S

Cooper CBG370S Intelligent Addressable Call Point (MBG813 / FXN501) Two versions of intelligent addressable callpoints are available in this range, the (CBG370S) which can be either surface or flush mounted and the (CBG370WP) which is a weatherproof version. Both the (CBG370S) and the (CBG370WP) are compatible with the Cooper range of intelligent addressable fire systems. These intelligent addressable callpoints are attractively designed, simple to install and are supplied as standard with a frangible glass element and a test key for ease of maintenance. A comprehensive range of accessories are available to maximise the functionality of the callpoint for particular applications. Key Features: Soft addressed Integral short circuit isolator Single address Fast fit clip on front cover High visibility status LED Wide range of accessories Heavy duty terminals

HOOTER WITH STROBE

GENERAL SPECIFICATIONS PRODUCT NAME Eaton Addressable wall sounder beacon CATALOG NUMBER CASB383 EAN 5021621406458 PRODUCT LENGTH/DEPTH 95 mm PRODUCT HEIGHT 105 mm PRODUCT WIDTH 105 mm PRODUCT WEIGHT .21 kg COMPLIANCES Contact Manufacturer APPEARANCE LENS COLOR Red COLOR HOUSING Red LIGHT COLOR Red PRODUCT BRANDING Eaton Cooper CONFORMANCE / CERTIFICATION EN CERTIFICATION STANDARDS EN54 Pt17 (Short Circuit Isolator) EN54 Pt3 (Fire Alarm Sounders) ENVIRONMENTAL DEGREE OF PROTECTION IP42 INSTALLATION CONSTRUCTION MATERIAL ABS MOUNTING METHOD Surface mounting CABLE ENTRY Rear SUITABLE FOR Wall Mounting

MANUAL CALL POINT 4099-9006

Simplex 4099-9006 Dual Action Pull Station (06501211) The Simplex 4099-9006 addressable manual station combines the familiar Simplex manual station housing with a compact communication module that is easily installed to satisfy demanding applications. Its integral individual addressable module (IAM) constantly monitors status and communicates changes to the connected control panel via IDNet or MAPNET II communications wiring. Activation of the 4099-9006 dual action manual station requires that a spring loaded interference plate (marked PUSH) be pushed back to access the pull lever of the single action station. Completing the action breaks an internal plastic break-rod ( Simplex 2099-9804 ). The use of a break-rod can be a deterrent to vandalism without interfering with the minimum pull requirements needed for easy activation. The pull lever latches into the alarm position and remains extended out of the housing to provide a visible indication. The Simplex 4099-9006 IDNet / MapNet II Dual Action Addressable Manual Pull Station is a replacement for the Simplex 4099-9003. This new pull station is equipped with an LED Indicator light that flashes during communications and is on steady when the station has been activated. The 4009-9006 is compatible with the Simplex Control Panels 4007ES, 4008, 4010, 4010ES, 4100ES, 4100U, 4020, 4100, and 4120 panels equipped with either IDNet or MAPNET II communications. Place your order today and we will ship your replacement pull station immediately.

Simplex smoke senser. Model 4098-9714

rueAlarm photoelectric sensors use a stable, pulsed LED light source and a silicon photodiode receiver to deliver consistent and accurate low power smoke sensing. Three user selectable sensitivities for special applications are available for each individual sensor, 0.2%, 0.5%, and 1% per foot. Standard sensitivity is 1.25% to 3.1% per foot. The fire alarm control panel runs an algorithm that can vary the sensitivity for normal applications between 1.25% and 3.1% per foot. Note: Fixed sensitivity settings higher than 1.0% per foot are not UL268 7th Edition compliant. The sensor head design provides 360 smoke entry for optimum response to smoke from any direction. Due to its photoelectric operation, air velocity is not normally a factor, except for impact on area smoke flow. Weight 0.50 lbs Dimensions 4.875 4.875 2.125 in Manufacturer Johnson Controls Brand Simplex Condition New Type Detector Style Plug-In Detectable Medium Smoke Detection Method Photoelectric Programming Set via Base Protocol IDNet, MAPNET II Voltage 24 VDC Voltage Range 18 32 VDC

Simplex Multy Sensor 4098-9754

TrueAlarm photoelectric smoke sensing and heat sensing combined in one housing to provide: Smoke activity accurately monitored by TrueAlarm photoelectric sensing technology Thermal activity accurately monitored by TrueAlarm thermistor sensing technology And TrueSense detection, a correlation of smoke activity and thermal activity providing intelligent fire detection earlier than with either activity alone For use with Simplex 4007ES, 4010ES, 4100ES, and 4100U fire alarm control panels: TrueAlarm analog sensor information is digitally communicated to the control panel via IDNet two-wire communications Special point types allow the 4098-9754 multi-sensor to communicate smoke and heat analog sensing data using only one IDNet address

Edwards EST SIGA-CT1 single input module

Weight 0.40 lbs Manufacturer UTC Fire & Security Brand Edwards, EST Condition New Type Intelligent Module Style Input, Monitor Programming Electronic Protocol Signature Loop Controller Status Indicator LED Voltage 19 VDC Voltage Range 15.20 19.95 VDC Series Signature Series

Fire alarm control Panel Agni

Brand AGNI Style Industrial Style Power Source Battery Powered Colour Multi Item Dimensions LxWxH 15 x 12 x 8 Centimeters Alarm Audible, Visual About this item 16X2 Character LCD Display Facility 1 to 4 Zone Expendable Inbult Battery attach facility Protected from high voltage Advance Micro Controller based circuit Compare with similar items

multy sensor

Electrical Specification Operating Voltage : 9 ~ 33V DC Reset Voltage : less than 1V Start-Up Current : 120 A. Alarm Current : 40 mA (Max) Remote Output : 15 mA maximum open collector Thermal Rating : 59 C (138 F) Rate of Raise of Temp : 11.1C / min (20F/min) Smoke Sensitivity : (1.9 0.76) % / ft Air Velocity : 0 4000 fpm. Operating Temperature : -10 C to 37.8 C Humidity : 0 95% RH, non-condensing Mechanical Specification Height : 46 mm with base Diameter : 100 mm dia Weight : 130 g with base IP Rating : IP 42

COOPER MULTI DETECTOR CAPT340

Cooper CAPT340 Intelligent Addressable Photo / Thermal Sensor (MAOH850 / FNX722 / 400004FIRE-0004X) This range of intelligent addressable sensors have been specifically designed to operate with Cooper intelligent addressable fire systems. All sensors are third party approved to the relevant section of EN54 (part 7 for smoke detectors & part 5 for heat detectors). The photo-thermal sensor (CAPT340) will respond quickly to fast clean burning fires yet maintain the advantage of optical sensors when detecting smouldering fires. The thermal enhancement of this sensor allows a higher alarm threshold which provides a greater rejection of false alarms. The sensor will also raise an alarm at temperatures exceeding 60C. Key Features Soft addressed Integral short circuit isolator Single address Wide range of sensor types 360 visibility LED using lightpipe technology Drift compensation Removable detector chamber Aesthetically pleasing Benefits Quick and simple to install Single "multi-mode" heat sensor Wide viewing angle for increased LED visibility Common mounting base Positive "lock" indication Discreet design for incorporation into any decor Easy to maintain/service

Edwards Speaker Model GC-S7

The Genesis line of ceiling life safety and emergency communications speakers and speaker-strobes combine high performance output with a low profile design to deliver a life safety signal solution thats as versatile as it is effective. While they are designed to mount inconspicuously overhead, these devices are also rated for wall-mounted applications. Clear-lens speaker-strobes are available in high and low candela models, which feature 15 to 95, or 95 to 177 cd output (see ordering information). Ceiling speakers feature 14 W to 2 W operation, which allows devices to be easily fine-tuned to achieve maximum benefit in exchange for the lowest possible system overhead. Light output and wattage tap settings are selectable with conveniently-located switches. Settings remain clearly visible even after final installation, yet they are locked in place to prevent unauthorized movement after installation. High fidelity models meet the NPFA 520 Hz requirements for newly construced commercial sleeping areas. They also produce crisp, clear voice audio output that is highly intelligible over large areas. These low-profile appliances feature textured housings in architecturally neutral white or eye-catching life safety red. Optional ALERT or FIRE markings make them ideal for applications that require differentiation between life safety and mass notification alerts. Standard Features High Fidelity 520 Hz speaker models available Field configurable no need to remove the device Ideal for Mass Notification appliances Unique low-profile design Unparalleled performance Easy to install Approved for public and private mode applications

SIEMENS MINI INPUT MONITOR MODULE XTRI-M

XTRI-M Mini Input Monitor Module, Built-In Isolator Model XTRI-M is one of several intelligent interface modules with Siemens Modular systems. Each mini interface module is designed to provide the means of interfacing direct shorting devices to the fire-alarm control panel (FACP) loop circuit. The module uses one (1) address on the loop.

Notifier Power supply ACPS-2406

FEATURES Each NAC can be synchronized with any of the following manufacturers audio/visual devices: either System Sensor (SpectrAlert Series) or Wheelock or Gentex Four NACs individually addressable by the FACP: 6.0 A of output power for NAC or 5.0 A of general purpose power. Each circuit can be DIP-switch-selected as general purpose 24 VDC power, four-wire detector power, or a Notification Appliance Circuit. Steady, March Time (120 PPM), Dual Stage, Temporal, or UZC Zone-Coded and Non-Coded devices all DIPswitch-selectable by circuit. Universal Zone Coder (UZC-256)/supervised output option allows for programmable coded outputs. Up to 256 different codes. Charges 7 to 25 AH batteries with full supervision. The charger on the ACPS may be disabled via a DIP switch. When disabled, a remote charger, for example a CHG-120, may be used to battery-back multiple ACPS supplies. AC loss detection and AC loss delay reporting. Brownout detection. Power-limited outputs. Isolated Signaling Line Circuit (SLC) interface. Selectable ground fault detection. Canadian dual-stage operation. Two Class A/B and two Class B (Style Y) only. A total of five (or less) ACPS power supplies may be connected together to synchronize multiple power supplies (connect to any NAC output from one ACPS to sync signal input single pair required).